Mechanical Tension Meters
Tension Meter – DX2
November 2, 2019
Mechanical Tension Meters
Tension Meter DX2-EDM
December 2, 2019

Tension Meter ETB and ETX

5 Tension ranges available
from 0.3 – 100.0 cN up to 3 – 2000 cN

For fibers up to 2000 tex and Cu wire Ø 0.5 mm

Electronic tension meter for hard to reach and limited access space applications.
Available in two models: ETB (Basic unit) and ETX (with memory and outputs)

Hand-held instrument with guide rollers up to max. 2000 m/min

Tension meter with measuring head as small as possible

Description

Special Features

• Tension meter ETB and ETX with guide rollers mounted on long shafts to reach into tightest places

• Hand-held instrument with ball-bearing mounted, V-grooved guide rollers up to 2000 m/min, for higher line speed use model ETPB or ETPX

• Coloured, backlight TFT display with 3 different display modes
– numeric
– numeric with live bargraph
– numeric with graph (time-tension)

• The display rotates in 90° steps for better reading

• Automatic “Zero-Setting” in each measuring position using a special sensor technique

• Selectable units of measurement: cN, g, N and lb

• Very high data sampling rate (internal 1 kHz)

• Storage of MIN, MAX, last reading, average and standard deviation per measuring interval

• User-set MIN and MAX alarms with indication of TFT display if reading is out of limits

• Adjustable electronic damping for better reading when tension fluctuates

• 3 separate calibration material memory locations for custom calibrations

• Calibration adjustment for fine tuning of the calibration if material differs from the used calibration material

• Menu set-up in English or German language

 

Standard Features

• Rugged aluminium housing

• LiPo accumulator (approx. 20 hours continuous operation) with AC adapter

• CE certified, interference resistant against static electrifications

• Certificate of Compliance with the order 2.1 according EN 10204 is included

• Optionally available: Inspection Certificate 3.1 according EN 10204 with calibration report.

 

Additional Special Features Model ETX

The tension meter ETX can be connected to a PC using the USB interface to monitor readings constantly on a PC

Memory for 60.000 readings

• 5 different memory modes can be selected by the operator:
• Mode S: only statistical values per series are displayed
• Mode H: storage of the X-Y-diagram for reviewing after finishing a series of measurement
• Mode C: continuous logging over a user set time and max. 999 series of measurement (2 Hz)
• Mode F: as C with higher sampling rate (200 Hz)
• Mode D: storage of single readings and statistic

besonderheiten-pc-verbindungModel ETX can be connected to a PC with the USB cable. With the software SW-TI3 »Tension Inspect 3« readings can be displayed, statistically analysed and saved. For more information see “Standard Accessories ETX”.

 

Available Models

Model Model Measuring Range Resolution Measuring Head Width* SCHMIDT Calibration Material**
ETB-100
ETX-100 0.3 – 100.0 cN 0.1 cN 24 mm PA: 0.20 mm Ø
ETB-200
ETX-200 2.0 – 200.0 cN 0.1 cN 24 mm PA: 0.20 mm Ø
ETB-500
ETX-500 2.0 – 500.0 cN 0.1 cN 24 mm PA: 0.20 mm Ø
ETB-1000
ETX-1000 3 – 1000 cN 0.1 cN 38 mm PA: 0.30 mm Ø
ETB-2000
ETX-2000 3 – 2000 cN 0.1 cN 38 mm PA: 0.50 mm Ø
*  Outer distance between outside guide rollers
** Suitable for 95 % of applications – PA = Polyamide Monofilamente, calibrated with a running filament approx. 100 m/min
Catalog
error: Content is protected !!